(as of Dec 27,2020 04:19:12 UTC – Details)
DB400 Remote dog training & anti bark dual action device, it’s perfect to training your dog, help you eliminate dog bad behavior or submit some of your basic command. You also can use the Anti bark mode to stop some of dog’s excessive squeaking behavior when you are not around, reduce neighbors complained
Channel 1 and/or 2 are used when you want to MANUALLY trigger a response when your dog barks or does a bad behavior that you want to correct. Channel A is used when you want the collar to AUTOMATICALLY trigger a response when your dog barks.
How to pairing the remote with the collar
Channel 1 and/or 2 are used when you want to MANUALLY trigger a response when your dog barks or does a bad behavior that you want to correct. You can use any of the three methods: beep, vibrate, or Electrostatic Pulse.
Hold the button on the collar down for 3 seconds. You will hear a beep and the LED light will flash green to confirm it is in pairing status. Within 10 seconds, press and hold one of the buttons on the remote (beep, vibrate, or Electrostatic Pulse) to pair the collar with the remote. When you hear the second beep, this confirms the pairing is complete.
Use the dial on the remote to set the intensity level from 1-100 for Channel 1 or 2.
If you want to pair another collar to the same remote, change the toggle switch to the second channel and follow the same instructions.
How to Pair Channel A – Anti Bark Mode
Channel A is used when you want the collar to AUTOMATICALLY trigger a response when your dog barks.
Have the remote in Channel 1 position on the toggle switch. Hold the button on the collar down for 3 seconds. hold one of the buttons on the remote (beep, vibrate, or Electrostatic Pulse) to pair the collar with the remote. When you hear the second beep, this confirms the pairing is complete. It is now in training mode. Next, change the toggle switch on the remote to Channel A position. It is anti bark mode now (default Shock+beep mode first time) . When you run back to the channel 1, it is training mode now. (if we selected vibrate+beep mode, then run to the channel 1 and then run to the channel A, it is vibrate+beep mode not Shock+beep mode)
How to set the sensitivity level
There are 5 levels to pick from and you will do this manually with the collar. You can change this at any time. (Note: The dial on the remote is not the intensity level for Anti Bark Mode.) Press and hold the button for 0.5 seconds to select the sensitivity level.
1 beep = Level 1
2 beeps = Level 2
3 beeps = Level 3
4 beeps = Level 4
5 beeps = Level 5
How to Test Anti Bark Mode
Gently scratch the test area back and forth on the back of the collar to verify that Anti Bark Mode is working. Level 5 is the easiest to test with.
To ensure the collar is 100% waterproof, make sure the rubber cover on the USB charging port on the back of the collar is fully sealed. If water gets into the collar and the collar vibrates for no reason, remove the collar from your dog, unscrew the screws, wipe out the water stains on the circuit board and the shell. Wait for it to dry, then re-install it and try again.
The dog training collar has a responding range of approximately 1,300 feet, which may slightly vary depending on the way the remote is held. Hold the remote out and away from your body to maintain an ideal range. When holding the remote, please do not touch or block the antenna to avoid a potential sharp decrease in the responding range. To ensure strong signals and connections, make sure the device is sufficiently charged before each use. 8. Range will not be limited through glass windows, but it will be limited through a door or wall.
3 remote training modes
Remote training collar with 3 modes, Beep, vibration. Dial to adjust vibration intensity Level from 1-100, very convenient to use, and you also can training 2 dogs as the same time just need Switch to the 1/2 channel for the first and the second dogs
2. Rechargeable & Waterproof Bark dog collar: Both of the transmitter and Collar are built-in lithium rechargeable battery with a normal standby last transmitter 90 days and collar 14days, come with a charger, and full charged just need 2-3 hours; Completely waterproof(remote not waterproof) of the Collar, Adjust nylon collar strap 8″-26″perfectly for dogs over 10lb
3. Dog Training & Dog bark collar, Can use as automatic Bark collar. First No need remote; Turn on the collar into anti- bark mode and default mode Beep+ S. Use remote; confirm remote and collar pairing successful, then switch the channel to A, By pressing S, vibration or Tone button to determine the working mode you need(Tone=Beep; Vibration=Beep + Vibration; S=Beep+ S).That means you just need to order our training collar can get remote training collar and Anti-Bark collar
4.Easy to use dog bark collar with remote, It has modes, Beep, vibration and Electrostatic Pluse. Dial to adjust vibration and S intensity Level from 1-100, very convenient to use, and you also can training 2 dogs as the same time just need Switch to the 1/2 channel for the first and the second dogs.
5.0ne Year Warranty: We are confident about our training collar for dogs, and we offer 12 Months Warranty. If you have any issue with our remote dog collar contact us by the service card email address, and we will always be more than happy to issue you a refund or make an exchange for you.